301 Stainless Steel Sheet/Plate

1. Thickness:0.1mm - 80mm
Width:800mm - 2,000mm
Length:300mm - 12,000mm

2. Surface:2B/HL/NO.4/8K
perforated,colored,checkered

3. Grades: Type 301 Stainless Steel

4. PVC film: Novacel(laser cutting)
Nitto(deep drawing)

5.Standards: ASTM/ASME UNS S30200

  • Type 301 stainless steel is a commonly available austenitic stainless with good corrosion resistance and elevated carbon to allow for cold working to a variety of tempers. It can be obtained in the 1/4 hard, 1/2 hard, and full hard.


    STANDARD CHEMICAL COMPOSITION

    Grade Cr Ni C Si Mn P S N
    301 min:16
    max:18
    min:6
    max:8
    max:0.15 max:1.00 max:2.0 max:0.045 max:0.030 max:0.10


    NOMINAL MECHANICAL PROPERTIES

    Grade/Temper Tensile Strength
    ksi (min.)
    Yield Strength 0.2%
    ksi (min.)
    Elongation% in 50 mm (min.)
    301 1/4 125 75 25
    301 1/2 150 110 18
    301 Full Hard 185 140 9


    NOMINAL PHYSICAL PROPERTIES

    Density lbm/in3 Coefficient of Thermal Expansion(min/in)ºF Electrical Resistivity mW-in Thermal Conductivity BTU-ft-ºF Melting Range
    0.29 at 68 - 212ºF at 68-932ºF at68-1450ºF at 68ºF at212ºF at392ºF at 68 − 212ºF 2550 - 2590ºF
    9.2 10.4 10.9 28.3 30.7 33.8 9.4

    APPLICATION OF 301 STAINLESS STEEL SHEET/PLATE

    • Aircraft structural parts
    • Trailer bodies
    • Utensils
    • Architectural and automotive rim
    • Roof drainage products
    • Conveyor belts
    • Variety of industrial applications
  • ADDITIONAL PROPERTIES OF 301 STAINLESS STEEL SHEET/PLATE

    • CORROSION RESISTANCE
      Type 301 Stainless Steel exhibits corrosion resistance comparable to Types 302 and 304 in most mild service conditions. Resistance to food service requirements and atmospheric corrosion is excellent. Stress cracking resistance is similar to Type 304. The optimal corrosion resistance is obtained in the cold worked then annealed condition. When Type 301 is heated or cooled slowly through a temperature range of 800 – 1600 °F (427 – 871 °C) without subsequent annealing, it may undergo carbide precipitation that may result in intergranular corrosion.
    • OXIDATION RESISTANCE
      The maximum temperature to which Type 301 can be exposed continuously without appreciable scaling is about 1600 °F (871 °C). For intermittent exposure, the maximum exposure temperature is about 1450 °F (788 °C).
    • COLD WORKING
      High hardness and strength for structural applications are achieved through cold working. In addition to the annealed condition 110 ksi (758 MPa) minimum tensile strength, Type 301 strip is normally produced in various cold-rolled tempers up to full hard 185 ksi (1276 MPa) minimum tensile strength.
    • FORMABILITY
      Type 301 can be readily formed and drawn. Due to its high work- hardening rate, intermediate annealing may be necessary for severe drawing and forming operations. Type 301 may not be suitable in certain severe forming applications where multiple forming operations are required.
  • SURFACE FINISH OF 301 STAINLESS STEEL SHEET/PLATE :

    *Not all finishes are available in all alloys - (contact Yieh United Sales for more information)

    #1 Finish Hot rolled, annealed and pickled.
    #2D Finish A uniform, dull silver gray mill finish that is applied to thinner stainless steel coils,the thickness of which has been reduced by cold rolling.
    #2B Finish A semi polished surface achieved by finishing with the equivalent of a 80 to 120 grit abrasive. This finish has a pronounced grit line.
    #3 Finish A semi polished surface achieved by finishing with the equivalent of a 80 to 120 grit abrasive. This finish has a pronounced grit line.
    #4 Finish Also called brushed, directional or satin finish. A is characterized by fine polishing grit lines that are uniform and directional in appearance. The final abrasive used in the process is 150 to 220 grit.
    #4 Satin Brush Finish 150 to 180 grit finish A fine directional polish, typically used in the washroom accessories industry. Most 3.5″ floppy diskette cover plates have this finish.
    #6 Finish Polished finish achieved with the equivalent of a 240 grit abrasive. Finer grit lines and higher reflectivity than a No. 4 finish.
    #7 Finish Highly reflective surface obtained with the equivalent of a 320 grit abrasive. Minimal grit lines.
    No. 8 or True #8 mirror This is the most reflective mirror finish on the market. All of the polishing, or “grit,” lines from the preliminary polishing operations are removed. The look is that of a glass mirror. Sometimes referred to as a non directional mirror finish, Super 8, No. 9, Perfect No. 10, and even No. 12 mirror.
    CMP Super #8 mirror Chemical Mechanical Polished Super #8 mirror finished sheets are guaranteed to be free from any manufacturing defects. This product represents the ultimate in mirror polished stainless steel. It is available as a single-sided or double-sided mirror polished sheet.
    Hairline finish 80 – 140 grit finish A well defined directional polish. Starting base substrate is a No. 4 finish sheet; these sheets are polished to provide a “continuous long grain” hairline look. A finish which is popular with architects for its aesthetic, it is equally popular with fabricators due to it’s ease of fabrication and finish matching properties after welding operations.
  • INNOVATIVE TECHNOLOGY of 301 STAINLESS STEEL SHEET/PLATE

    At Yieh United Corporation, we never stop improving and developing our technologies to go beyond our customer’s expectations. We strive towards these goals to produce reliable products and ensure they can be fully utilized throughout their lifetime.

    stainless-steel-innovative-technology

  • PACKING FOR 301 STAINLESS STEEL SHEET/PLATE

    Our 301 stainless steel products are packed and labeled according to the regulations and customers’ requests.

    stainless-steel-sheet-standardpackageNote: This is Yieh United Corporation’s standard seaworthy packing for 301 stainless steel sheet sheet/plate.

    stainless-steel-sheet-special-packageNote: This is Yieh United Corporation’s special packing for 301 stainless steel sheet/plate (Extra fee is needed).

  • FAQ

    1. What is the minimum order quantity (MOQ)?
    - Normally, the MOQ for our stainless steel sheet is 200 Kg. If we have any excess inventory of stainless steel sheet, there’s no MOQ requirement. You can ask us to check when you are interested in purchasing them.

    2.What is the payment method?
    
- For new customers: 30%T/T deposit 70%T/T Before shipment.
– For partners and distributors, 30%T/T deposit 70% T/T Against B/L Copy.

    3.What is the acceptable currency?
    - We accept USD, EUR and RMB.

    4.What is the delivery time?
    
- 5 days in advance.

    5.Where is the loading port?
    - Normally, our loading ports are Shanghai, Tianjin, and Shenzhen. You can choose anyone of them, or you can select the other ports.

    6.What is the delivery term?
    - FOB, CIF, CFR, EXW

    7.Do you offer free samples?
    
- Yes, based on our stock status, we will send our customer free samples. The express fee is to be paid by our customers.

Inquiry Box


 

Search

Available Services

Services