
1. Thickness:0.1mm - 80mm
Width:800mm - 2,000mm
Length:300mm - 12,000mm
2. Surface:HL/NO.4/8K
3. Grades: Type 304/304L Polished Stainless Steel
4. PVC film: Novacel(laser cutting)
Nitto(deep drawing)
5.Standards: ASTM/ASME S30400/S30403
GAUGE REFERENCE [restabs alignment="osc-tabs-left" responsive="false"] [restab title="Specification" active="active"]Type 304/304L Stainless Steel is the modern evolution of the original “18-8” austenitic stainless steel. It is an economical and versatile corrosion resistant stainless steel suitable for a wide range of general purpose applications.
Yieh United Co. Stocks over 25 grades of polished stainless steel sheet in a variety of finishes, including HL, #4 Brush, and #8 Mirror finish. We also can supply specialty finish to satisfy your exact requirements including polishing both sides of the sheets, long grain finishes, non-directional stainless steel sheet finishes, #6 finish, #7 finish or per customer requests.
STANDARD CHEMICAL COMPOSITION
Grade | C | Mn | Si | P | S | Cr | Ni | N |
304 (S30400) | 0.07max | 2.0max | 0.75max | 0.045max | 0.03max | min:18.0 max:20.0 |
min:8.0 max:10.5 |
- |
304L (S30403) |
0.03max | 2.0max | 0.75max | 0.045max | 0.03max | min:18.0 max:20.0 |
min:8.0 max:12.0 |
0.10max |
NOMINAL MECHANICAL PROPERTIES
Grade | Tensile Strength ksi (min) |
Yield Strength 0.2% ksi (min) |
Elongation% | Hardness(Brinell) MAX |
Hardness(RockwellB) MAX |
304 (S30400) | 75 | 30 | 40 | 201 | 92 |
304L (S30403) |
70 | 25 | 40 | 201 | 92 |
NOMINAL PHYSICAL PROPERTIES
Density lbm/in3 |
Thermal Conductivity BTU/hr-ft-ºF |
Electrical Resistivity (in x 10-6) |
ModulusOfElasticity (psi x 106) |
Coefficient of Thermal Expansion (min/in)-ºF x 10-6 | SpecificHeat (BTU/lb/ºF) |
Melting Range(ºF) | Melting Range |
at 68ºF | 9.4 at 212ºF | 28.3 at 68ºF | 28 | 9.4 at 32 - 212ºF | 0.1200 at 68ºF to 212ºF | 2500 to 2590 | |
12.4 at 932ºF | 39.4 at 752ºF | 10.2 at 32-1000ºF | 2552ºF | ||||
49.6 at 1652ºF | 10.4 at 32-1500ºF |
APPLICATION OF 304/L POLISHED STAINLESS STEEL SHEET/PLATE
304/L Polished stainless steel sheets are now widely used in elevator doors, column covers, ceiling panels, escalator decorative cladding, curtain walls, revolving entrance, door & window frames, canopies, wall and corner guards, grilles and screens, ornamental handrails & railings, wall panels, storefront displays & nightclubs, architectural signage systems, phone cases, clipper sets and name plates.
1. For kitchen equipment
2. For Kitchenware
3 For elevator
REASONS TO CHOOSE 304/L POLISHED STAINLESS STEEL SHEET/PLATE
1. Raw Material
Our coil is originated from Taiwan, Krupp, Columnbia, Baosteel, TISCO, and other major steel production of high quality stainless steel. If coil is not from a good standard factory, the coils surface may have some problems, especially for the edge. They are not easily leveled and processed, after processing, there will be some vertical strips which make the surface not expected. Here is an example to show the bad finished surface is due to the material origin.
Note: these white strips cannot be removed by polishing.
2.Sandbelt
In the processing, sandbelt working time is a key factor for controlling the surface quality. If the sandbelt is new, the polished lines will be very rough and thick, and have less reflective effect.After the sandbelt has been used for a long time depending on the quality of the sandbelt,the polished strips maybe too shallow,which cannot reach the expected effect.
3.Film
After the surface processing, choosing the PVC film will have much influence on afterwards application. We have several kinds of film to be chosen, and they are suitable for different application. The film not only serves as a protection but also affect the afterwards processing.
>>Laser film
Laser film is considered to be one of the best film. The thickness is at least 10c. Laser film normally has higher melting degree than other film, which will not be melted and sticked on the surface after heat treatment. Here is an example of normal film after heat treatment.(Please confirm the downstream processing, and then decide which film is to be applied.)
>>Black and white film imported from other countries except China
This kind of film cannot undertake high temperature treatment, but it is relatively thicker and more sticky than Chinese Origin film. It can be used in most mechanical process and have a good performance.
>>Transparent blue film and Chinese black and white film
These two kinds of film are relatively not considered to be good qualified, which means they are not very sticky, and not thick enough. The thickness ranges from 2c to 10c. Most customers apply these film in many ordinary processing. When the downstream need bending, or deep drawing, the film may suffer from cracking.
OTHER SURFACE FINISHES OF 304/L POLISHED STAINLESS STEEL SHEET/PLATE
*Not all finishes are available in all alloys - (contact Yieh United Sales for more information)
#1 Finish | Hot rolled, annealed and pickled. |
#2D Finish | A uniform, dull silver gray mill finish that is applied to thinner stainless steel coils,the thickness of which has been reduced by cold rolling. |
#2B Finish | A semi polished surface achieved by finishing with the equivalent of a 80 to 120 grit abrasive. This finish has a pronounced grit line. |
#3 Finish | A semi polished surface achieved by finishing with the equivalent of a 80 to 120 grit abrasive. This finish has a pronounced grit line. |
#4 Finish | Also called brushed, directional or satin finish. A is characterized by fine polishing grit lines that are uniform and directional in appearance. The final abrasive used in the process is 150 to 220 grit. |
#4 Satin Brush Finish | 150 to 180 grit finish A fine directional polish, typically used in the washroom accessories industry. Most 3.5″ floppy diskette cover plates have this finish. |
#6 Finish | Polished finish achieved with the equivalent of a 240 grit abrasive. Finer grit lines and higher reflectivity than a No. 4 finish. |
#7 Finish | Highly reflective surface obtained with the equivalent of a 320 grit abrasive. Minimal grit lines. |
No. 8 or True #8 mirror | This is the most reflective mirror finish on the market. All of the polishing, or “grit,” lines from the preliminary polishing operations are removed. The look is that of a glass mirror. Sometimes referred to as a non directional mirror finish, Super 8, No. 9, Perfect No. 10, and even No. 12 mirror. |
CMP Super #8 mirror | Chemical Mechanical Polished Super #8 mirror finished sheets are guaranteed to be free from any manufacturing defects. This product represents the ultimate in mirror polished stainless steel. It is available as a single-sided or double-sided mirror polished sheet. |
Hairline finish | 80 – 140 grit finish A well defined directional polish. Starting base substrate is a No. 4 finish sheet; these sheets are polished to provide a “continuous long grain” hairline look. A finish which is popular with architects for its aesthetic, it is equally popular with fabricators due to it’s ease of fabrication and finish matching properties after welding operations. |
INNOVATIVE TECHNOLOGY of 304/L POLISHED STAINLESS STEEL SHEET/PLATE
At Yieh United Corporation, we never stop improving and developing our technologies to go beyond our customer’s expectations. We strive towards these goals to produce reliable products and ensure they can be fully utilized throughout their lifetime.
[/restab] [restab title="Packing"]PACKING FOR 304/L POLISHED STAINLESS STEEL SHEET/PLATE
Our 304/304L polished stainless steel products are packed and labeled according to the regulations and customers’ requests.
Note: This is Yieh United Corporation’s standard seaworthy packing for 304/304L stainless steel sheet sheet/plate.
Note: This is Yieh United Corporation’s special packing for 304/304L polished stainless steel sheet/plate (Extra fee is needed).
FAQ
1. What is the minimum order quantity (MOQ)?
- Normally, the MOQ for our stainless steel sheet is 200 Kg. If we have any excess inventory of stainless steel sheet, there’s no MOQ requirement. You can ask us to check when you are interested in purchasing them.
2.What is the payment method?
- For new customers: 30%T/T deposit 70%T/T Before shipment.
– For partners and distributors, 30%T/T deposit 70% T/T Against B/L Copy.
3.What is the acceptable currency?
- We accept USD, EUR and RMB.
4.What is the delivery time?
- 5 days in advance.
5.Where is the loading port?
- Normally, our loading ports are Shanghai, Tianjin, and Shenzhen. You can choose anyone of them, or you can select the other ports.
6.What is the delivery term?
- FOB, CIF, CFR, EXW
7.Do you offer free samples?
- Yes, based on our stock status, we will send our customer free samples. The express fee is to be paid by our customers.
[/restabs]
Inquiry Box
[contact-form-7 id="4" title="Contact form 1"]